홈페이지> 제품 리스트> 수평 슬러리 펌프> ZJW 피딩 펌프> 밀 연삭 공급 펌프
밀 연삭 공급 펌프
밀 연삭 공급 펌프
밀 연삭 공급 펌프
밀 연삭 공급 펌프
밀 연삭 공급 펌프
밀 연삭 공급 펌프

밀 연삭 공급 펌프

$5000≥1Set/Sets

지불 유형:L/C,T/T,Paypal,Money Gram,Western Union
인 코텀:FOB,CFR,CIF,EXW,FAS,FCA,CPT,CIP,Express Delivery
최소 주문량:1 Set/Sets
수송:Ocean,Land,Air,Express,Express
포트:Tianjin,Qingdao,Guangzhou
제품 속성

모형65ZJW

상표나이푸

TypeClay Wet Sand

Casting MethodThermal Gravity Casting

Sand Core TypeClay Sand Core

ApplicationMachinery Parts

MachiningBoring Machine

MaterialSteel

Surface TreatmentSand Blast

Surface RoughnessRa0.4

StandardGB

CertificationISO 9001:2008

65ZJW Feeding Pumps65

포장 및 배송
판매 단위 : Set/Sets
포장 종류 : 나무 케이스
사진 예 :
제품 설명

65 개 zjw 필터를 눌러 먹이 펌프

캔틸레버 수평 원심 슬러리 펌프 / 고무 늘어선 슬러리 펌프 / R55 슬러리 펌프 / 그랜드 시일 슬러리 펌프 / 원심 시일 슬러리 펌프 / 방수 고무 슬러리 펌프 / 교체 슬러리 세탄 슬러리 / 펌프 모래와 자갈 처리 슬러리 펌프 / 폐수 처리 슬러리 / 펌프 착용 미네랄 부유 처리 펌프 / 세탄 펌프 먹이 / 펌프 / 펌프


Naipu® NP-ZJW 시리즈 필터 프레스 이송 펌프의 고유 유압 desin 설치 모드를 적용

임펠러 펌프의 성능 곡선은 일반 펌프보다 가파른 있는지 확인에 사용하기 더 적합

필터 프레스 피드, 큰 용량을 실현하기 위해서, 저항의 변화에 따라 변한다

저압 공급 및 저용량은 고압 펌프 filter.The 널리 석탄 washery에 사용

등 환경 보호, 알루미늄 공장, 제련 공장



건축 도면

drawing-1





공급 펌프의 구조 차트

1.Two 상 류트 2. 두 상 임펠러

3.One 상 와권 4.Back 판

5.Feeding 방 6.Locating 부시

7.Expeller 8.Expeller 커버 플레이트

9.Decompression 본체 10.One 상 임펠러

11.Tie 바 12.Shaft 슬리브

13.Cover 판 14.Disassembly 링

15.Water 누름판 16.Bearing

17.Shaft 18.Bearing 스페이서 슬리브

19.Bearing 커버 20.Frame

21.Bent 파이프



NP-ZJW PUMP 선택 차트

selection chart



NP-ZJW 공급 펌프의 성능 매개 변수

Performance Parameters


제품 개요:

Filter Press Photos


가능한 오류와 타협.


        Faults

    Reason

      Settlement

1.Pump fails to discharge any water,The hand of pressure gauge beat violently

1.Suction pipe don`t have enough water.

2.Suction pipe blocked or the valve is locked.

1. Inject enough water

2.unlock the inlet valve,clear the blocks

3.Exclude the air leakage

2.The pump can`t discharge water,the hand of vacuum meter beat heavily.

1.The inlet valve is unlocked or silted up.

2.The resistance of suction pipe is too big or silted up.

3.The height of suction is too high.

1.Unlock the valve or desilting

2.improve the design of  suction pipe or desilt

3.Lower the height of the installation.

3.The pump can`t discharge water,pressure gauge shows heavy pressure.

1.The resistance of the discharge pipe is too big.

2.The impeller blocked

3.The speed is slow.

1.Check and adjust the outlet pipe.

2.Clear the impeller

3. Improve the speed.

4.The pump doesn`t rotate

The volute is silted up by the blocks.

Clear the blocks

5.The capacity is not enough

1.The blocks of the impeller or the inlet or outlet pipe.

2.The abrasion of the impeller is heavily.

3.The speed is low to normal

4.Pump is installed unreasonably or the leakage of the inlet pipe.

5.The transporting height is too high,the loss of the resistance of the inside pipe are too big.

6.The inlet valve not open enough or blocked

7.The packing seal leaks

1.Clear the impeller or pipe.

2.Change the impeller

 

 

3.Adjust the speed

4.Install again or stop leaking.

 

 

5.Decrease the height of the transport or reduce the resistance.

6.Unlock the inlet valve

 

7.Compress the packing tightly

6.The motor of the pump is overloaded

1.The head of the pump exceeds the head of the working condition.

2.Not consider the slurry density when selecting the pump.

3.The packing press tightly

1.Turn down the outlet valve,cut the impeller or lower the speed.

2.Select the motor again.

3.Adjust the the screw of the  packing gland

7.Abnormal sound in the pump, and no water out

1.The resistance of the inlet pipe is too big.

2.The height of the suction is too high.

3.Cavitation occurred

4.there is air in the inlet

5.The temperature of the liquid is too high

1.Clear the suction pipe and sluice valve.

2.Lower the height of the suction

3.Adjust the water valve and let the pump operate in the defined limits.

4.Block the leakage.

5.Lowering the liquid temperature.

8.pump vibrates

1.pump cavitate

2.The block of the impeller single vane

3.The no concentricity  between the pump shaft and motor shaft

4.Fasteners or foundation loose

1.Adjust the water valve ,lower the height of the installation,reduce the resistance of the inlet.

2.Clear the impeller

3.Alignment again

4.Fasten the screw,and reinforce the foundation.

9.Bearing is overheat

1.lock the cooling water

2.lubrication is not good.

3.the lubrication oil is not clear

4.the wrong direction of the thrust bearing.

5.there is something wrong with the bearing.

1.Open the cooling water

2.Adjust the oil quantity

3.Clear the shaft,change oil

4.According to the inlet pressure,adjust the direction of the thrust bearing.

5.Change the bearing

10.Packing short life

The material of packing is not good

Change the packing

11.pump leak oil

1.High oil level

2.The rubber parts invalid  

3.Assembly problem

1.Lower the oil level

2.Change rubber spares

3.Adjust the assembly

 

12 Pump head leaking

1.The rubber parts not press well

Assembly again or press tightly 





자주하는 질문:

Q1. 당신은 제조 공장이 있습니까?

예, 우리는 직접 제조 공장이며,이 분야에서 10 년 이상의 경험이 있습니다.

당신이 판매에 재고 제품을 Q2.Do?

일부는 우리는 주식에있다, 그러나 다른 사람 없습니다. 우리는 항상 고객의 요구 사항에 따라이 제품을 생산하기 때문에.

장점 Q3.What 당신은 할 수 있습니까?

답변 : 우리는 직접 제조 업체와 가격 경쟁력이있다.

B : 우리의 엔지니어는 정말이 지역에 experieced 있으며, 우리는 당신에게 OEM 서비스를 할 수 있습니다.

C : 우리는 공장, 우리는 그렇게 지키는 배달에 관해서는, 생산 일정을 정렬 할 수 있습니다.


연락처:

석가장 Naipu 펌프 (주).

추가 : No.368 뉴타운 북쪽 도로, 석가장 하이테크 산업 개발구, 허베이, 중국, 050,091을.

전화 : 0086-311-897162903

팩스 : 0086-311-87162902

담당자: Karen Tan

스카이프: karen_naipump











  • 질문 보내기
질문 보내기
*
*

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

송신